|
|
| (91 intermediate revisions by the same user not shown) |
| Line 1: |
Line 1: |
| − | (0.7E temporary to-do)
| |
| | | | |
| − | == LFS client ==
| |
| − |
| |
| − | ;New keys
| |
| − | : ??
| |
| − |
| |
| − | ;New commands
| |
| − | :/status none|F9|F10|F11|F12|next|prev - sets status screen
| |
| − | :E.g. /status next will cycle through the F9 to F12 status screens
| |
| − | :(you could assign it to a CTRL+ or ALT+ key and then a wheel button)
| |
| − | :
| |
| − | :/liveset and /pitins - do the functions of F11 and F12 menus
| |
| − | :
| |
| − | :You can use operators:
| |
| − | := (set value)
| |
| − | :+= (add to value)
| |
| − | :-= (subtract from value)
| |
| − | :
| |
| − | :Examples:
| |
| − | :/pitins ftyre = r3 : change front tyres to R3 in pit stop
| |
| − | :/pitins rtyre = super : change rear tyres to road super
| |
| − | :/pitins fpressure = 1.1 : set front tyre pressure to 1.1 bar
| |
| − | :/pitins fpressure += 0.1 : increase requested pressure by 0.1 bar
| |
| − | :/pitins cancel : cancel all pit instructions
| |
| − | :/pitins tyres always : change all tyres
| |
| − | :/pitins tyres 20 : change tyres if wear > 20%
| |
| − | :/liveset bbal 60 : set brake balance to 60%
| |
| − | :/liveset rarb -= 0.1 : decrease rear ant-roll bar by 0.1
| |
| − | :
| |
| − | :Available options for /pitins:
| |
| − | :fuel, tyres, repair, symmetric
| |
| − | :ftyre, fcamber_l, fpressure_l, fcamber_r, fpressure_r, fwing
| |
| − | :rtyre, rcamber_l, rpressure_l, rcamber_r, rpressure_r, rwing
| |
| − | :cancel, fcamber, fpressure, rcamber, rpressure
| |
| − | :
| |
| − | :/pitins pressure commands can accept unit (psi/bar) (no unit = bar)
| |
| − | :E.g. /pitins fpressure 30 psi
| |
| − | :
| |
| − | :Available options for /liveset:
| |
| − | :bbal, farb, rarb
| |
| − |
| |
| − | ;Multiple commands on single line:
| |
| − | :
| |
| − | :Multiple commands can now be added on a single line which sometimes
| |
| − | :can avoid the need for a script file, e.g. to set a button to
| |
| − | :change tyres in pit stop, you could use a double command:
| |
| − | :/pitins ftyre super /pitins rtyre super
| |
| − | :
| |
| − | :NOTE: some commands cannot be followed by another command:
| |
| − | :/say /echo /join /rcm /pass /msg /altf /ctrlf
| |
| − |
| |
| − | ;others:
| |
| − | :/h_mass username X - set added mass for user's car
| |
| − | :/h_tres username X - set restriction for user's car
| |
| − | :/teamarrows=no/yes - arrows on non-race small map use name colour
| |
| − |
| |
| − | ;lights:
| |
| − |
| |
| − | :Side lights, low and high beam headlights are now supported
| |
| − | :Text command /light (requires two parameters) to switch lights:
| |
| − | :/light ind [off/left/right/all] - switch indicators/hazard lights
| |
| − | :/light head [off/side/low/high/low_off/low_high/next/prev] - lights
| |
| − | :/light [rfog/ffog/extra] [off/on/toggle] - switch fog/extra lights
| |
| − | :/light all [off/on] - switch all switchable lights off/on at once
| |
| − | :Key '3' now toggles between off & low beam like /light head low_off
| |
| − | :SHIFT+3 goes through all headlight states like /light head next
| |
| − |
| |
| − | == Editor ==
| |
| − | ;Modeller hotkeys / shortcuts:
| |
| − | :
| |
| − | :CTRL+O: load main object
| |
| − | :
| |
| − | :Keys for subob, point, tri, map, cutout, page modes:
| |
| − | :CTRL+D: duplicate
| |
| − | :CTRL+N: new
| |
| − | :DELETE: delete
| |
| − | :
| |
| − | :H: hide selected (points or triangles)
| |
| − | :SHIFT+H: hide unselected
| |
| − | :ALT+H: unhide all
| |
| − | :
| |
| − | :E: extrude selected points (with trace enabled in point mode)
| |
| − | :S: select selection's points / select connected triangles
| |
| − | :CTRL+F: flip selected triangles (in tri mode)
| |
| − | :CTRL+F: flip connected triangles (in point mode)
| |
| − | :CTRL+I: invert selection (points or triangles)
| |
| − | :ALT+M: Merge points (previously known as Fuse points)
| |
